PM583 with acs 355 VFD in PROFINET control

I have a PM583 with PROFINET Master ,ACS355 with PROFINET adapter. i tried to control the drive . but in plc side, while scannig am not able to get a VFD as a slave device. Kindly suggest a right way to complete this communication.

Comments (0) New comment

vigneshwaran92rce Rank: 144

Asked 1 year ago

Answer this question Follow

Answers

You use Control Builder Plus or Automation Builder? The drive use Fena-01 or Fena-11 device?

Have you correct defined the IP adress in ACS355?

You must define menu as follow:

51.01 Ethernet

51.02 10 - PNIO DRIVE PROFILE

51.03 1 - 1= 100Mbps full duplex

51.04 0 - static IP

51.04 198 - first part of IP adress

51.06 168 - 2nd part of IP adress

51.07 20 - 3rd part of IP adress

51.08 10 - 4th part of IP adress

51.09 24 - subnet mask

51.10 198 - gateway adress

...

You need to follow the FENA instruction for Profinet use

PLC side

Make sure to have correct define the station name and the same IP adress that you have associate to drive.

Without other information, I could not give you more suggestions

Hope this help you

Comments (11) New comment

by vigneshwaran92rce Rank: 144 on 3/26/2017 1:23:35 AM | Like (0) | Report

Dear sir, am using automation builder software, FENA 11 . I will try tomorrow and give a feedback sir

by vigneshwaran92rce Rank: 144 on 3/26/2017 10:32:01 PM | Like (0) | Report

I did all the things as per your advice. but that MODULE LED blinkikg in green colour.

by Flavio Mussolin AKS expert

Rank: 4 on 3/26/2017 10:50:31 PM | Like (0) | Report

You still noticed some change from your previous situation?
Which green LED flashes on the communication module? During normal operation, the network LED flashes as host and module should be fixed

by vigneshwaran92rce Rank: 144 on 3/26/2017 10:55:54 PM | Like (0) | Report

I mentioned in my earlier msg, that module led is blinking

by vigneshwaran92rce Rank: 144 on 3/26/2017 11:05:45 PM | Like (0) | Report

host and network led is ok.
module led blink with green colour

by Flavio Mussolin AKS expert

Rank: 4 on 3/26/2017 11:08:22 PM | Like (0) | Report

Perhaps I did not explain. You must tell me what LEDs are blinking, because each flashes has a different meaning.

by vigneshwaran92rce Rank: 144 on 3/26/2017 11:13:48 PM | Like (0) | Report

MODULE LED

Flashing
green

Device needs commissioning due to
configuration missing, incomplete or
incorrect. The device may be in the Standby
state.
This may also be caused by the adapter
waiting for Duplicate Address Detection to
complete. If Duplicate Address Detection has
detected an IP conflict, the IP is configured to
0.0.0.0 and can be reconfigured by PLC.

Kindy see that PROFINET IO – Diagnostics in FENA 11 manual

by Flavio Mussolin AKS expert

Rank: 4 on 3/26/2017 11:17:26 PM | Like (0) | Report

There is something wrong. The module LED is generally fixed, and the network should be flashing, indicating that it is working on 100 Mbps.
With these few indications I can not understand where is the error, you should send a copy of your sw PLC and ACS355, so I can analyze them.

by vigneshwaran92rce Rank: 144 on 3/26/2017 11:19:29 PM | Like (0) | Report

can u give me a team viewer support now? all the setup is ready.

by Flavio Mussolin AKS expert

Rank: 4 on 3/27/2017 12:00:13 AM | Like (0) | Report

What I can do is give you some suggestion, I can not replace the ABB direct support service in your area

by vigneshwaran92rce Rank: 144 on 3/27/2017 3:17:43 AM | Like (0) | Report

I did communication. Ip conflict is the problem . Anyway thanks for your support

Add new comment

Flavio Mussolin AKS expert

Rank: 4

Answered 1 year ago

Question details

PM583 with acs 355 VFD in PROFINET control

Answers

Other questions needing answers

Related Topics

AKS experts