AC800F demo mode

English version : google translated

Good afternoon I would like to inform about the monitoring software for AC800F builder. Currently I have the software in demo mode for 100 days, but if you can do some downloading to the controller without a license. I watched the tutorial and upload an app to be going the way of man icon commissioning of the helmet, but when I select that button closes the application, do not know if I have something wrong or permanently installed without license I can not make downloads and testing with real equipment. In addition to this, I can not add DTM Profibus slaves, to add an AO card for Profibus remote I had to install the gsd CI830 module, this is also due to demo mode?.

thank you very much

Spanish version :

Buenas tardes me gustaria informarme sobre el software control builder para el AC800F. Actualmente tengo el software en modo demo por 100 dias, pero no se si se puede realizar alguna descarga al controlador sin tener la licencia. He visto el tutorial y para poder cargar una apliación se debe ir al modo comisionamiento del ícono del hombre con el casco, pero cuando selecciono ese botón se cierra la aplicación, no sé si tengo algo mal instalado o definitivamente sin la licencia no puedo realizar descargas y realizar pruebas con el equipo real. Adicionalmente a esto, no puedo agregar esclavos profibus DTM, para agregar una tarjeta remota de AO por profibus tuve que instalar el gsd del módulo CI830, esto también es debido al modo demo?.

Muchas gracias

Comments (1) New comment

canesmaior Rank: 1797

Asked 7 years ago

Answer this question Follow

Voted best answer

Hello,

If I understood correctly, you have freelance installed in demo mode and it is not possible to go in comissioning mode and not possible to add profibus slave DTM. If so

Regarding DTM, CI801 and CI840 profibus slaves are selectable/supported via DTM. there is no relation with demo and licensed version.

The function is same in both demo/licensed version, so even in demo mode it is possible to download to controller.

Want to confirm did you downloaded freelance software in demo mode first time on that computer ? or before there was licensed version and you have downloaded software in demo mode now ? Which freelance version you are using ? If it's your first time with freelance recomended to go through getting started manual available in demo dvd. or

@ http://www05.abb.com/global/scot/scot296.nsf/veritydisplay/dccb84483ca27155c125
78da004a094c/$file/3BDD012560R05_en_Freelance_9.2SP1_Getting_Started.pdf

Hope this helps

Comments (5) New comment

by canesmaior Rank: 1797 on 10/8/2013 1:09:24 PM | Like (0) | Report

Good afternoon. Thank you very much for your reply. the main problem I had was with the version of the operating system, installing the software on Windows XP if I could start commissioning mode. I could not connect to AC800F, but now I have problems with the remote module declaration Profbus communication. I'd like to find out about this setup, I'm declaring an FI 830F in the rack and I have a CI830 for remote I / O, but for some reason I can not see what is as remote, I have not much information about how the teams are declared and how to set the speed of the master side and slave side, not if there is a manual procedure or just talk about this, because I have searched but have not found anything. Could you please guide me in this matter?

by Sumit Gargav AKS expert

Rank: 4 on 10/8/2013 11:27:43 PM | Like (0) | Report

which freelance version you are using ? check manual 3BDD012515R04/3/201 there you can find profibus configuration details.Regarding speed at master side you can configure at node PROFI_M_DEV > double click > bus parameter and at slave side you need to select only bus address no need to configure speed. Moreover in cbf configuration mode in HW tree double click on PROFI_M_DEV > window get open > Click on help button > say ok to popup, you will get help about profibus click > next button to follow more information.

by canesmaior Rank: 1797 on 10/9/2013 8:03:00 AM | Like (0) | Report

Good day. again thanks for your reply. I am using the Demo version 9.1.6985. Regarding the manual that tells me, could you please send me some link to download? I searched the code on the page tells me ABB but I can not, as well as on the web either. or is there a site where you can review and downloading on these settings. Again thank you very much in advance.

by Blanchard Rank: 1133 on 10/10/2013 9:35:00 PM | Like (0) | Report

I have seen weird things like this before if you are using V9.1 you should be running a Windows 7 32bit OS if you are not that might be a concern.

by Blanchard Rank: 1133 on 10/10/2013 9:39:12 PM | Like (0) | Report

Correction I think 9.1 requires Windows XP with SP3. In any case the OS may be your part of your problem

Add new comment

Sumit Gargav AKS expert

Rank: 4

Answered 7 years ago

Answers

Hi,

If i understood correctly,

Question 1: Unable to download the application in demo mode?

Ans: Create the application in CBF, go to "Project" menu available in main menu and select "Commissioning", R.click on Process station-> select load whole station.

Note: Download to controller is possible in both demo and licensed mode.

Question 2: Unable to add Profibus DTM slaves?

Ans: Please check whether you insatalled FDT DTM components, if not please install by selecting "Modify" option during installation.

Please provide Freelance version which you are using...

I hope this helps you...

Comments (0) New comment

Sounder Rank: 105

Answered 7 years ago

Question details

AC800F demo mode

Voted best answer

Answers

Other questions needing answers

Related topics

AKS experts