AC500 eCo Web Server

Hello
I'm trying to start web server function in automation builder V2.2 and codesys V2.3, java V7, CPU PM554 TP ETH with firmware version 2.8.
when i type URL "http://192.168.0.10/webvisu.htm"; 192.168.0.10 is CPU IP address, a white page opens and visualization not displayed. The question for me is whether the target system should be connected directly to PLC via Ethernet? or should the target system and CPU be connected to an Internet network? In second case, how should IP addresses be set?

Comments (0) New comment

elhambv7 Rank: 3616

Asked 25 days ago

Answer this question Follow

Voted best answer

Hi

what kind of browser are you using? Remember that most browsers no longer support Java, perhaps Internet Explorer is an exception.

BR

Flavio

Comments (1) New comment

Flavio Mussolin AKS expert

Rank: 4

Answered 25 days ago

Answers

Hi,

Pls, confirm which browser is using for web visu. I'm not sure about chrome but Internet Explorer will do the job

Confirm these too,

You have added this site to the trusted sites in Internet Explorer
Java is added to the Internet Explorer
Web Server protocol is activated in Automation Builder and in Codesys resources
ensure your system is in with the same network of PLC You can do it with direct connecting or a switch also even you can do through the internet(I never did Internet I have done it locally so I can't help you in the Internet case)

Pls confirm all and

Comments (6) New comment

by elhambv7 Rank: 3616 on 9/27/2020 11:36:28 PM | Like (0) | Report

Hi Amal,
Thank you for your attention.
I followed your first three points.
1) I implemented the application program on cpu by ethernet, selected 'creat boot project' and then 'run'. Is it possible to create the same network with the RJ45 direct cable between CPU and target System? I tried this but got no answer and i saw a white screen loading ( A message appears stating that you are using Java).

2) Do i have to resemble cpu IP address with network IP address manually? ,If i put the CPU and target system on the same internet network.

by Amal Rank: 102 on 9/28/2020 2:18:22 AM | Like (1) | Report

Hi,

Of course, you can make it using LAN Cable

Please give the same IP address to your PC which is in the same network of the PLC and check the signal using the ping command

Do Network Ip mapping manually rather than DHCP
If you share your PLC IP and Subnet I can give the IP for the system(just change the last digits in IP configuration and Subnet should be the same in both

I hope you got clear if any doubts let me know I will try my best to help you

by elhambv7 Rank: 3616 on 10/6/2020 3:59:38 AM | Like (0) | Report

Hi Amal,
Your comments are very helpful and clear. I do all of them, but i didn't reach a conclusion! I'm confused and do not know what to do
IP addresses of PLC and PC are similar to network address. This time a white screen is not displayed and a 404 error is seen.
Thank you for Your patience in responding...

by Amal Rank: 102 on 10/6/2020 4:05:54 AM | Like (0) | Report

Hi,

I am still unaware of the issue can you please share the project here also the IP given to the PC and PLC and the mode of communication between them

I have faced a lot of issues while I have tried my webserver for the first time so I hope I can help you out

by elhambv7 Rank: 3616 on 10/6/2020 5:00:30 AM | Like (0) | Report

If Possible, give me your email to send my project for you.
Thanks a lot

by Amal Rank: 102 on 10/6/2020 5:03:51 AM | Like (0) | Report

amaljoseph143aj@gmail.com

Add new comment

Amal Rank: 102

Answered 25 days ago

Question details

AC500 eCo Web Server

Voted best answer

Answers

Other questions needing answers

Related topics

AKS experts