Downgrade Firmwire for HIContoller
Dear Expert,
I have problem regarding downgarde firmwwire for HI Integrity Controller.
Current condition we have some component with new firmwire :
1. PM865HI ==> 5.1.1400.15
2. SM811 ==> 5.1.1400.0
3. CI867 ==> 5.1.2403.0
We want to downgrade this firmwire to series :
1. PM86HI ==> 5.0.2410.28
2.SM811 ==> 5.0.2404.0
3. CI867 ==> 5.0.2501.0
I have tried with control builder remote system, but when tyring to send the firmwire to hardware it show "Communication Error".
I know that we can downgrade controller with serial and I have tried this for upgrade methode and I know how to use it.
But my questions if we can downgrade controller, how to downgrade SM811 and CI867? as I tried SM811 can't be seen in remote system firmwire check if firmwire controller is different ?
I have problem regarding downgarde firmwwire for HI Integrity Controller.
Current condition we have some component with new firmwire :
1. PM865HI ==> 5.1.1400.15
2. SM811 ==> 5.1.1400.0
3. CI867 ==> 5.1.2403.0
We want to downgrade this firmwire to series :
1. PM86HI ==> 5.0.2410.28
2.SM811 ==> 5.0.2404.0
3. CI867 ==> 5.0.2501.0
I have tried with control builder remote system, but when tyring to send the firmwire to hardware it show "Communication Error".
I know that we can downgrade controller with serial and I have tried this for upgrade methode and I know how to use it.
But my questions if we can downgrade controller, how to downgrade SM811 and CI867? as I tried SM811 can't be seen in remote system firmwire check if firmwire controller is different ?
Voted best answer
Greetings,
For downgrading firware you can not use ethernet connection. You have to use TK212 cable and COM4 port on CPU.
This can be done for only CPU not any CI modules.
Could you please try it via this way?
Please see below link Section-5:
https://library.e.abb.com/public/5d62...
Hope it helps you.
For downgrading firware you can not use ethernet connection. You have to use TK212 cable and COM4 port on CPU.
This can be done for only CPU not any CI modules.
Could you please try it via this way?
Please see below link Section-5:
https://library.e.abb.com/public/5d62...
Hope it helps you.
Answers
Hi,
AC 800M Controller firmware and its CI modules can be upgraded independently.
Below link might help for downgrading CI867.
https://forum-controlsystems.abb.com/...
AC 800M controller firmware and the SM810, SM811, SM812 (safety) CI modules must be upgraded simultaneously.
I think single engineering node with downgraded software may help you out.
AC 800M Controller firmware and its CI modules can be upgraded independently.
Below link might help for downgrading CI867.
https://forum-controlsystems.abb.com/...
AC 800M controller firmware and the SM810, SM811, SM812 (safety) CI modules must be upgraded simultaneously.
I think single engineering node with downgraded software may help you out.
Hi,
AC 800M Controller firmware and its CI modules can be upgraded independently.
Below link might help for downgrading CI867.
https://forum-controlsystems.abb.com/...
AC 800M controller firmware and the SM810, SM811, SM812 (safety) CI modules must be upgraded simultaneously.
I think single engineering node with downgraded software may help you out.
AC 800M Controller firmware and its CI modules can be upgraded independently.
Below link might help for downgrading CI867.
https://forum-controlsystems.abb.com/...
AC 800M controller firmware and the SM810, SM811, SM812 (safety) CI modules must be upgraded simultaneously.
I think single engineering node with downgraded software may help you out.
Hello Titus and Dash,
Thanks for the help, finally can downgrade firmwire for sm811 and ci867.
Step are explain below :
- Downgrade using serial upgrade firmwire first (sbin file can copy from existing that running downgrade firmwire)
- after finish downgrade primary and secondary you can start ip config for new controller, or for exsiting controller no need
- connect PM865, SM811 an CI867 to system you want to downgrade by using remote system from control builder (sm811 must be enable "access enable" input 2)
- show firmwire and start to downgrade
Thanks for the help, finally can downgrade firmwire for sm811 and ci867.
Step are explain below :
- Downgrade using serial upgrade firmwire first (sbin file can copy from existing that running downgrade firmwire)
- after finish downgrade primary and secondary you can start ip config for new controller, or for exsiting controller no need
- connect PM865, SM811 an CI867 to system you want to downgrade by using remote system from control builder (sm811 must be enable "access enable" input 2)
- show firmwire and start to downgrade
Add new comment