Can someone tell me how to add ACS880 library in control builder?

Currently I am using control builder 5.1.0 version with AC800M PM861APLC, and 4 nos. of DCS800 drive and 01 no. of ACS800. Now i want to replace ACS800 drive with new ACS880. For this purpose I first need to add library in PLC program. When I am trying to insert new library in "S800IoModulebusHwLib", the option is not enable. (see picture).

PLease advice how can I insert ACS880 library in this section?

CB.jpg

Comments (0) New comment

shoaib3012 Rank: 839

Asked 2 years ago

Answer this question Follow

Voted best answer

Have you tried using the ABB Engineered drive? It does not state ACS800 in the library. It is just DDCS over optical modulebus. Engineered drive in the control builder end is the same for ACS800 using system software and ACS880 (i.e. using datasets from 10 and so on). ABB Standard drive is in use when data sets starts from 1.

Comments (3) New comment

mpetter78 Rank: 138

Answered 2 years ago

Answers

Hi,

Follow the below steps to add new hardware Library,

Hardware Right Click-->Insert/replace hardware type(s) and create library with any name as you required and browse the GSD file for Particular ACS880 drive and Map the signals according to Data types provided by vendor.

Comments (9) New comment

by shoaib3012 Rank: 839 on 3/20/2018 1:21:13 AM | Like (0) | Report

Hi,thanks for responding.please see my attachment,I am doing the same but insert/replace hardware option is not enable.

by Dash AKS expert

Rank: 21 on 3/20/2018 1:41:48 AM | Like (0) | Report

Hi shoaib, i hope you have already reserved your project before adding any hardware lib.

by shoaib3012 Rank: 839 on 3/20/2018 2:02:03 AM | Like (0) | Report

We have been using this program since long, now going to upgrade some hardware

by shoaib3012 Rank: 839 on 3/20/2018 2:03:04 AM | Like (0) | Report

Can you help me further to resolve my problem

by Deepak.S Rank: 24 on 3/20/2018 8:57:37 AM | Like (0) | Report

Are you trying to Establish Profibus Communication Between ACS880 and ABB DCS?

by shoaib3012 Rank: 839 on 3/20/2018 9:24:44 AM | Like (0) | Report

No.3 dcs and 01 acs800 drives are already communicating with fibre optic through NDBU branching unit. I want to replace ACS 800 drive with newer version ACS880,therefore need to add acs880 library in S800IoModulebus file inside the HW library. hope you understand my need

by Deepak.S Rank: 24 on 3/20/2018 10:02:40 AM | Like (0) | Report

You can create a new library for ACS880 drive know why you need to create under S800IO modules.

by shoaib3012 Rank: 839 on 3/20/2018 10:15:26 AM | Like (0) | Report

Because I need to connect new drive in place of old drive with the same protocol.i will send connected hardware to you

by Deepak.S Rank: 24 on 3/21/2018 1:04:04 AM | Like (0) | Report

ya by creating new library for ACS880 and connect to hardware library then you can replace the library with ACS880.

Add new comment

Deepak.S Rank: 24

Answered 2 years ago

Hi See the attached Image and follow the steps,Click new Library and give name as per your requirment and extract GSD files according to Data exchange file.

Comments (0) New comment

Deepak.S Rank: 24

Answered 2 years ago

Please see atatched photographs of control builder manual, ABB engineered drive and ABB standard drive does not support ACS880

Comments (0) New comment

shoaib3012 Rank: 839

Answered 2 years ago

Untitled.jpg

Question details

Can someone tell me how to add ACS880 library in control builder?

Voted best answer

Answers

Other questions needing answers

Related topics

AKS experts